The SwitchPilot Servo can be used with DCC or Motorola\u00ae protocols. It is compatible with the DCC norm and reacts to switch commands. It is possible to operate turnouts from 01 to 508 under Motorola\u00ae use. Recognition of control mode is fully automatic.<\/p>\n
The SwitchPilot Servo is being powered either directly by the digital central station itself or separately by a DC- or AC source (transformer). RC servos or ESU servo motors can be directly connected to its four servo outputs. The 5V voltage needed as well as the special control impulse is generated by the SwitchPilot Servo itself. For each servo, not only lever speed can be adjusted individually but also its end positions. Thus it is possible to operate especially prototypically slow and powerful turnout motors, independent of track- and gauge systems. You could also employ the SwitchPilot Servo for driving signal arms or railway crossings. Also the automatic opening of engine shed doors does not need to remain a dream.<\/p>\n
The SwitchPilot Servo can be programmed especially comfortably: For one it supports all DCC modes of programming including POM (programming in the main). Assuming a command station with an outlet for a programming track, all adjustments can be controlled and modified. As RailCom\u00ae is integrated, it is also possible to read out and control recent settings, even during operation. Alternatively you can use the comfortable three-button input: You are able to control addresses, the end positions of all four servos and the corresponding motion speed directly, during operation and without any complicated programming- at all command stations!<\/p>\n
The Switch Pilot Servo would not be a typical ESU product, if it had not even more to offer: You can operate the decoder without the use of a command station! Conventional switches can be controlled with the help of eight switch inputs. Therefore fans of \u201cclassic\u201d analog model railway can benefit from the advantages of the servo motor. In other words: the SwitchPilot Servo does not need a command station to switch and set servo paths as well as speed.<\/p>\n
Do you need some relay outputs in addition to the servo outputs, since you intend to polarize the frog, for instance, or switch off the track voltage within the signal line section? Then you should extend your SwitchPilot Servo with the SwitchPilot Extension relay module: one of its four twin-relay contacts switches simultaneously to the servo and can be used for potential-free load swichting \u2013 ideal for tricky circuitry!<\/p>\n
As it has been the case with our loco decoders, in the design phase\u00b4s greatest emphasis has been placed upon near indestructibility of the SwitchPilot Servo decoders. That means ESU quality is also built into our stationary decoders, now and in the future! You can rely on it!<\/p>\n
The internal software of the SwitchPilot Servo V2.0 can be replaced by a more up-to-date version at any time. This is done with the aid of the ESU LokProgrammer. That way everything remains current in case of changes in the standards and you may also profit from new functions.<\/span><\/p>\n \u00a0<\/span><\/p>\n \u00a0<\/p>\n SwitchPilot Servo V2.0<\/p>\n","protected":false},"featured_media":47224,"template":"","meta":{"_acf_changed":false},"product_brand":[952],"product_cat":[1957],"product_tag":[],"class_list":["post-47223","product","type-product","status-publish","has-post-thumbnail","product_brand-esu","product_cat--accessory-decoders","first","outofstock","purchasable","product-type-simple"],"acf":[],"yoast_head":"\n\n\n
\n Operational modes:<\/td>\n NMRA\/DCC \u201eAccessory Decoder\u201c compatible<\/td>\n<\/tr>\n \n \u00a0<\/td>\n Motorola\u00ae compatible up tp 127 addresses. K83 compatible.<\/td>\n<\/tr>\n \n \u00a0<\/td>\n Powered either by command station or separately DC- or AC source (transformer) up to 18V.<\/td>\n<\/tr>\n \n Servo Control:<\/td>\n 4 servo outputs for RC servos (ESU, Graupner\u00ae JR\u00ae or Futaba\u00ae compatible), 1.0ms to 2.0mS pulse length, positive. Lever speed and end positions separately adjustable.<\/td>\n<\/tr>\n \n RailCom\u00ae:<\/td>\n Integrated RailCom\u00ae feedback for reading CVs on the main track and reporting the servo position to the command station.<\/td>\n<\/tr>\n \n Input keys:<\/td>\n Programming either directly to command station via DCC or input key, consisting of 3 buttons and LED display (5 LEDs) for direct address indication as well as two end positions and lever speed of all 4 servos.<\/td>\n<\/tr>\n \n Dimensions:<\/td>\n 95mm x 85mm x 22mm (3.74 inch x 3.35 inch x 0.87 inch)<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n","protected":false},"excerpt":{"rendered":"